Question:While trying to get the hub motor up and running here we have run in to some problems. After installing the hub motor wheel in the fork it was very sluggish to turn and took quite a bit of effort, not freewheeling at all. The first time we plugged the battery (fully charged 48V 12AH LiFePo4 at 52.9V) in to hub motor (without the throttle connected to the controller cable) the hub motor beeped three times. When we hooked up the controller cable black and yellow pin connectors to the corresponding ones on the throttle there was no response from the electric bike motor, but the battery level lights did light up. We tried both throttles sent with the same results.

As it was the weekend I went to the forum and looked there for assistance. I received some good feedback that the 3 beeps we heard were a signal that the throttle was not work which is what we found as soon as we hooked up the throttle. We have checked all the leads for correct amperage as per his instructions with positive results.

I am assuming that electric bike kit is bench tested before it leave there? The packaging was undamaged upon delivery and all seemed in good order upon receipt. If you could please advise us on what to do to get this resolved we would appreciate it as we want to get on with our trials here to be able to get out product to market by summer.

I have checked my throttle and hub motor controller wires against your PDF diagram and there seems to be some discrepancy? I wish my camera was working but I will describe my findings. Diagram Throttle Black 3 pin shows: Red? perhaps Orange?/White/Blue Our Throttle Black 3 pin has:
Orange/White/Black from core with black jump to yellow 2 pin Diagram Controller Black 3 pin has: Red? perhaps Orange?/black/Yellow Hub Motor Controller Black 3 pin has: Rust from Core with Red Jumper to PAS White three pin/White/Black from core with Black jumper to yellow 2 pin

I checked the 8 pin connector again and can’t see that it isn’t making good contact. No bent pins or obstructions.Electric Bike Motor still beeps three times upon connecting to full battery as described with and without full connections of cables.

Yes jumping the two holes as indicated does make the electric bike kit run. It seemed like at first that by moving the controller wire that the electric bike motor would stop and start as if there was a short right at the junction and we thought that might be the problem. We hooked up the cable but I still am not getting any response from either throttle when hooked up to the black two pin connector even if I move the cable at the junction and now using the jumper the short method that issues seems to have gone away?

We are trying hard to make this electric bike kit work here but I have to admit we are getting a bit frustrated. The throttle cable while hooked up shows 5.0 amps on the red wire and from .8 amps at rest and 3.8 amps on the white wire when at full throttle like it should? Without the black pin connector together there are 5.0 amps at the red wire and .1 amps at the white wire if that is any useful information.

Hub motor,electric bike motor,electric bike kit supplier: Leaf Motor Technology Co.,Ltd

Good day.I have bought from you 1 set of 48V 1000W rear electric bike kit that includes 48V 12Ah li battery,48v lcd brushless motor controller,twist throttle,brake levers with 26″ 1000w hub motor rear wheel.Received all things.The order number lf283218U578679K. Shipment was fast and packing box was not broken.

But since I had installed hub motor wheel,motor controller,throttle..everything, I had following problems: Twist throttle was sometimes hard to begin electric bike motor uphill, with even slightest elevation.Electric bike kit either stops unintentionally, while I begin to accelerate hub motor, or doesn’t start at all. Usually it takes several amperes to start throttling.Electric bike motor never gets hot, only a little bit warm.

Electric bike kit (regenerative) brakes almost didn’t work at all. It is possible to stop with them only from the lowest speed of 5km/h approximately. If the speed is more than this, brakes just let the hub motor to freewheel. I don’t know if they are converting electrical energy.

When I tried to use USB cable to see, if it is because of lcd hub motor controller settings, I couldn’t connect to it. Software starts, when I choose “Connect” nothing happens with the program itself, only the electric bike motor starts to beep constantly. “Get settings” didn’t load any, changing parameters and saving them seems to have no effect on the electric bike motor. Only “Disconnect” button worked, but somehow it says that “Get settings” is complete, and any changes in parameters reset to their initial state. After approximately 360km, “Cruise control” button stopped to work. I opened hub motor and checked electrical connection to the motor controller itself, the button itself and wires are functioning properly. But I have absolutely no voltage reading on the button’s wires.

Read article from blog and forum,I doubt the problem comes from electric bike battery.It as said,there is a BMS inside lithium battery.Some cells would be dead because of overcharge or over discharge.If dead,can’t charge lithium battery.Even if charge it,green led on charger will light at once.It looks like full charge,actually no any electrical energy inside battery.So when I ride my hub motor electric bike,the electric bike motor will stop in short time.

Please, help me to resolve those electric bike kit problems, especially, with “Cruise control” button.

Hub motor,electric bike motor,electric bike kit supplier: Leaf Motor Technology Co.,Ltd

I have recently bought a DIY electric bike kit from you, where I have bought a 36V battery and a 48V hub motor & brushless motor controller. I thought that when I ordered from your online internet shop, you would check, that the electric bike kit system would work..

On the homepage you write, that I can force the 48V hub motor controller to work with lower voltages.Also, the 48V thumb hub motor controller does not work. The twist controller works.

I have called your office and found out, that the problem is, that the 48V hub motor controller cuts off the electric bike kit system to protect the li battery. And the only solution is to manually override the system, but that is not an ideal way to operate the e-bike.

I have now ordered a new hub motor controller and thumb throttle for 36V from your homepage. What I would like you to do, is to write on the package you send me, that the package you send me is a guarantee replacement.

I do not wish to discuss guarantee and other issues with you, it is much easier for me to order new parts, but I would like to avoid to have to pay customs and VAT again for the same things. Also it takes weeks before the goods get through customs.

I also have one more suggestion for improvement:Please put 2*2 nuts on the electric bike motor wheel to be able to secure them, because my front 48V 1000w electric bike motor wheel fell off while I was starting with the e-bike. (while driven by 36V, ½ power – where I pull the break lever, push the cruise control 5 times, and use the cruise control to operate the electric bike motor) Also it would be nice if you could specify how hard I should tighten the nuts on the electric bike motor wheel.

20Nm? 60Nm?, I would like to tighten them well, but I do not wish to brake the thread. My transaction ID of electric bike kit order is 3FA78294KK410865B

Hub motor,electric bike motor,electric bike kit supplier: Leaf Motor Technology Co.,Ltd

Electric bike hub motor kit was gone, how to solve it?

Received my electric bike kit .Product list:
1.26″ 36V 250W front brushless geared hub motor wheel
2.36V 6-MOSFET brushless motor controller working with LCD(display speed,mileage,battery gauge..)
3.standard black twist throttle with battery gauge
4.brake lever with low voltage to brake
5.three button-ON/OFF switches that are used for control front&rear lights,cruise,horn…

Check rim whether in the middle of fork and the direction of hub motor runs.Then I have installed everything on my bicycle according as instruction manual and the electric bike kit worked fine.

I was running e-bike about 25km and then I stopped the electric bike motor . Charged the electric bike battery because I was staying there for some hours. Started on the way home and after some heavy hills (about 3 km)it was completely dead. The electric bike kit system was running like normal up to this, but suddenly all power on the electric bike motor wheel was gone.

Those three led lights on twist throttle for electric bike battery were still lit. I tried to turn e-bike off and on again, but same result. Today the electric bike kit is still dead.

Do you have any idea? Measured 0,1 Ohm between the electric bike motor(hub motor phase wire: yellow, green, blue).Infinity between hub motor cable and hub motor cover. So it does not look like it is burned. The electric bike motor controller has 41,8 Volt input.

Measure the hub motor hall sensor:
Red, black, yellow, blue, green wires.
1.The voltage between red and black is 4.5V;
2.The voltage between yellow and black is 4.2V or 0V,(When use hand to turn hub motor, the voltage will change from 0~4.5V~0~4.5V)
3.The voltage between blue and black is 0.2V; (When use hand to turn hub motor, the voltage could not change)
4.The voltage between green and black is 0.1V. (When use hand to turn hub motor, the voltage could not change)

From above test data, I doubt there were two hall sensor inside the electric bike motor that were broken.

Electric bike hub motor kit was gone, how to solve it?

Hub motor, electric bike motor, electric bike kit supplier: Leaf Motor Technology Co., Ltd

Bought 1 set of electric bike kit from one supplier in China two months ago. Sent more than 10 emails, haven’t gotten any reply. I met below issue, hope solve it.

When I was riding my electric bike three weeks ago, the 250w mini front hub motor suddenly started to make a strange and strong noise. If I try to turn the twist throttle on when the e-bike doesn’t have any load, I keep the hub motor wheel in the air. The electric bike motor works fine and electric bike kit does not make any noise.

However, if I try riding my electric bike and turning the throttle on, the electric bike motor starts making a strong and continuous noise. I tried to riding my bike keeping the brakes continuously pressed and any noise appears so it seems to be some electric problem. It is very strange and I am so much worried.

I took off electric bike kit wheel and used screwdriver to disconnect six screw nuts, took apart hub motor cover and found there was a rotor-winding, two bearings, three sets of 42-gear, 1 set of 21-gear on the axis, 1 set of 81-gear on the hub. There wasn’t any impurity inside the hub motor. Re-install and test electric bike motor wheel, still have the same problem. Don’t know what’s the problem.

Contact my supplier many times and can’t get any reply. I looked for answers by google, yahoo and bike forums, still can’t find the correct answer. Yesterday I got a message from my US friend about there was a company, leaf motor can help me. So I sent an email to leaf motor.

Surprisingly just half an hour past, leafmotor replied me and asked me to check the bearings. How to check hub motor bearing? Take off two bearings from axis, and use little finger to hold inside of bearing, the other hand to turn bearing, faster, better. If you can hear some noise from bearing that can confirm the problem comes from electric bike motor ‘s bearing. At last, I found there was a bearing was broken. According as the bearing model, I bought two new ones in market and replaced them.

Test electric bike kit wheel in the air, no noise. Brake hub motor wheel, still no noise. Nice, Have solved it.

I should thank leaf motor that help me and I found fun through repairing electric bike motor. Now I decide to buy leaf ‘s electric bike kit if I have need and will recommend my friends to order leafmotor’s electric bike motor, bike kit…

Though I haven’t ordered any goods from leafmotor by now. But they are very professional, has best service and believe they have high quality products.

Hub motor, electric bike motor, electric bike kit supplier: Leaf Motor Technology Co.,Ltd