Category Archives: BLDC motor - Page 4

leaf 20 inch 48V 1500W rear hub motor – bike conversion kit

Posted by on December 30, 2021 Comments Off on leaf 20 inch 48V 1500W rear hub motor – bike conversion kit

Q: Regarding: Newest 20 inch 48V 1500W rear hub motor – bike conversion kit works on any bike.

What is the max current of the hub motor controller at 48V?
Is the controller programmable to other max current settings?
Does the LCD display show power either in watts, or volts and amps?

A: It’s max 40A
This bike motor controller can set other max speed.
Yes,LCD display power

Q: If I order just the hub motor, can the 1500W rear hub motor have a 10K NTC thermistor installed in it?

A: This 1500w hub motor with 10k themistor (It’s default)

Q: I have a 135mm fork. Can the Shimano Freewheel, 7 Speed, 14-28T be installed on the hub motor and still fit within 135mm?

A: Shimano 7 speed screw-on sporket can be install this hub motor.(TZ-21) – It’s default. Also,fit for 135mm fork.
If other shimano 7 speed cassette sprocket,need to modify hub motor.(We still can make.)

Q: Thanks. Do you sell a Shimano sprocket with an 11 Tooth (11T) that would fit the 1500W rear hub motor?
Q: Can you list the description of each wire in the hall/temperature connector pictured below?
red – ?
black – ?
yellow – ?
white – ?
green – ?
blue – ?

A: Red +
Black –
Yellow – W
White – Temp
Green – V
Blue — U

Q: What parts is includes on this 20 inch 48V 1500W rear bike motor kit?

Package Content:
1 x 20 inch Newest 48V 1500W rear hub motor wheel
1 x 48V 1500W 12-MOSFET motor controller
1 x LCD ( display speed, mileage, battery gauge.. )
1 x Twist throttle — Cable length: 1500mm
1 x Brake levers — Cable length: 1500mm
1 x Three button switches ( control cruise, regen brake, reverse .. ) — Cable length: 1500mm
1 x Pedal assist — Cable length: 1500mm

Net Weight: 11.0 kg / 24.2 lbs
Package Size: 50cm L x 23cm W x

50cm H / 19.7″ L x 8.7″ W x 19.7″ H
Package Type: Cardboard Box

1500w hub motor rpm

Posted by on December 30, 2021 Comments Off on 1500w hub motor rpm

I have done a little more testing with the 1500w hub motor. I think that I am
happy with the current winding. I am giving the motor 65A battery, 180
amps phase.. and it is like a rocket now.
The efficiency is very good.. the most efficient hub motor I have
tested.. good work!

But I want to be sure about the winding for my post about your 48V 1500W bike motor,
because your webpage shows lots of different RPM for the same motor (
this is confusing )..

If someone orders the hub motor from your website.. they will receive a 16*4
turn motor, which is 650rpm @ 49v = 13.26 kV
And the 13*5 turn motor would do 550rpm @ 49v = 11.2 kV
Is this correct…?

P.S. If you are interested in having a hub motor re-seller.. I told someone
in the USA about your hub motors and told him about my tests.

I got the hub motor and have tested it. It’s a great hub motor, but the winding is too fast for a 26 inch,650B,700C,28 inch,29 inch hub motor wheel.It’s better for 14 inch,16 inch,18 inch,20 inch,24 inch bike motor wheel.

The no load speed on the hub motor I received = 640rpm on 49v.

I notice on your web page that you sell stator windings.. I was wondering
how many turns this hub motor has.

Is it possible that you could sell me a stator winding with one more turn that could do 500-550rpm on 49v?

16 * 4T 650RPM
13 * 5T 550RPM
11 * 6T 450RPM
9 * 7T 350RPM
8 * 8T 250RPM
7 * 9T 150RPM
…………

18 inch gearless brushless hub motor for electric bike

Posted by on December 30, 2021 Comments Off on 18 inch gearless brushless hub motor for electric bike

I am interested in the 18 inch rear gearless bldc hub motor provided by leaf bike company and I had a few questions about the hub motor.

1) What is the rated torque?
2) What is the maximum torque?
3) How many poles are there in this hub motor?
4) Does it contain any brakes? If so, what type? (Disc/Drum/V-brake)
5) Does it contain hall sensors? If so, How many and what is their description?
6) Most importantly, is this motor a brushless dc motor (BLDC) or a permanent magnet synchronous motor(PMSM)? This greatly affects my choice, as both types are sometimes very close to each other, so I needed verification on what type it was.
7) Does it have a waterproof gradient?
8) Dimensions: I had an issue with the dimensions listed in the description compared to dimensions in the drawing for the motor on Leaf Motor site. I am actually looking for a motor that is around 16 inches, however, I chose the 18 inches because the image for the 18 inches shows the diameter being 372 mm which is equal to around 14.6 inches, which isn’t 16 inches but is very close. The diameter of the electric bike motor is crucial for my wheel choices and so clarifying what the actual diameter of this motor would be very helpful, I can’t risk not being sure of the dimensions as I am currently designing the vehicle and need to be very accurate, and that’s why a professional mechanic is needed specialized in this kind of vehicle, because sometimes people think a person who’s good with cars will be good at bikes too.
9)Does this motor support regenerative braking?
10) What is the back EMF of this motor?
Finally, I would like to apologize if these are too many questions but I am in need of the maximum clarifications I can get to be as precise, so any information you can provide will help me on my quest to find the best. I will be forever grateful for your help.

A:
Please click our new site.
https://www.leafbike.com/products/e-scooter-hub-motor/18-inch-electric-motor/
There is more drawing & performance.

* This 18 inch is fit for 18 * 2.125 or 2.5 tire.
The dia. of this 18 inch is 372mm, it’s fit for 18 inch bike tire.

* 46 pcs magnet, with 3 pcs hall sensor… It’s brushless motor.

48V,1000W, 1500W rear hub motor for 20 inch or 24, 26, 27.5, 700c 28, 29inch

Posted by on December 30, 2021 Comments Off on 48V,1000W, 1500W rear hub motor for 20 inch or 24, 26, 27.5, 700c 28, 29inch

Do you have a more detailed drawing for dimensions of the 48V 1000W,1500W rear hub motor? I am particularly interested in the dimension I marked “A” so I can be sure the brake rotor disc will fit correctly.

The drawing from your web site shows the left side of the hub motor on the right side of the drawing. Also, in the video the hub motor is installed backwards and the rear derailleur is just hanging off the bike on the cable. Very confusing, but eventually I understood that the person who installed your hub motor on the bike put the motor in backwards, with the wire coming out the right side even though your specifications say the wire comes out the left side.

I suggest that you make all of your drawings, pictures, and video consistent left to right, because they are presently mixed up.

Here is an example of a drawing that is correct left versus right and has all the dimensions a bicycle builder needs to be confident the motor will fit the bicycle.

If I order with a free hub to use a cassette is the free hub body replaceable?

Does it look something like this?

Do you have a part number or a link for the replacement free hub and cassette for that motor?

Thank you very much for all the information, I really like this hub motor but I need to make sure it will fit and work well for my bike.

700c 48V 1500W rear hub motor – bike conversion kit

Posted by on December 29, 2021 Comments Off on 700c 48V 1500W rear hub motor – bike conversion kit

Q: 700c 48V 1500W front hub motor – bike conversion kit
Item ID #LBCK700C481500FN

Newest 700c 48V 1500W rear bike motor – conversion kit
Item ID #LBCK700C481500RN
What is the difference between these 2 bike conversion kits?
Can I get them with black spokes?
What is the winding (such as 12T, 8T, 6T, etc)?
Does it come with sprockets (rear cogs, or cassette)? If not, what kind do I order for it?
How much does it cost and how long does it take to ship to California, USA?

A: 1.They are the same motors.
LBCK700C481500FN is fit for 100mm rear dropout. Fit for front fork. Can’t use disk brake. ONLY use V brake on rim.
LBCK700C4815000RN can be installed sprocket on this motor. Fit for 135mm rear dropout. Fit for rear fork. Can install disk brake on rear motor. Also can use V brake on rim.

2. Black spokes ,, okay.. But it takes about 3 days to wait for this black spokes (Please leave message when you order)

3. Default: 5T. But we can make 6T, 8T … (Please leave message when you order)

4. LBCK700C481500FN can’t use sprocket.
LBCK7004815000RN can install sprocket. But Not come it. You can install yours on our hub motor. (Please leave message when you order rear cogs or cassette, then we can make motor as your sprocket. If No message, default: motor with screw thread for cogs

Q: You said:”3. Default: 5T. But we can make 6T, 8T … (Please leave message when you order)”
I have not read about an odd number such as 5T. Is this correct that your default is 5T?
Also, Do you have a right half twist throttle available for this instead of the right full twist?

A: Generally 700c 48V 1500W hub motor,use 5T.
If you leave message: 5T when you order (or send an email to us after paid) – It must 5T.
Yes. We also have other throttle. Please click below site. All throttles are fit for this bike conversion kit LBCK700C481500RN.

Also, leave message: what throttle. We will ship it instead of that full twist.

Motor controller with LCD-003 from Leaf Bike

Posted by on December 29, 2021 Comments Off on Motor controller with LCD-003 from Leaf Bike

48V 1000W-1500W-2000W, 36V 250W-500W-750W, 24V 250W Motor controllers with LCD-003 from Leaf Bike are used to drive 8-9-10-12-13-14-16-17-18-20-22-24-26-27.5-700C-28-29er inch hub motor bike wheels.

How to set max speed?
If you feel 20 inch or 24 inch,26 inch, 700c, 28 inch, 29 inch hub motor kit is too fast,please set it to be low speed.
* Press “sw/middle button” from LCD more than 2 seconds,then LCD will display.
* Press “up & down button” together more than 2 sconds until 72 is flashing ( 72 is kmh, if you hope works 20mph / 32kmh, press “down” to be 32)
* Press “sw/middle” button one time to save,then 24 is flashing.. (24 is hub motor wheel size. Don’t set)
* Press “sw/middle” button one time to save,then kmh or mph is flashing..
* Press “sw/middle” button one time to save,then press “sw/middle” button more than 2 seconds until be back.

Turn throttle,motor will work max speed as your setting.

—————
There is a “ 5 or 4 or 3 or 2 or 1 or 0” on the Left side of LCD.
* Be “0” – throttle & pedal assist NOT work.
* Be “1” – throttle works (If install pedal assist, pedal about 3 circels,then can drive motor to work)
* Be “2” – throttle works (If install pedal assist, pedal about 2.5 circels,then can drive motor to work)
* Be “3” – throttle works (If install pedal assist, pedal about 2 circels,then can drive motor to work)
* Be “4” – throttle works (If install pedal assist, pedal about 1.5 circels,then can drive motor to work)
* Be “5” – throttle works (If install pedal assist, pedal about 1 circels,then can drive motor to work)

If NOT install that pedal assist,ONLY use throttle to drive motor. But Should be 1 or 2 or 3 or 4 or 5.(Be 0,turn off throttle)

——————————–
How to use three button switch?
1.We cut off that blue wire.It’s for reverse. If reconnect this blue wire.
This yellow button be left / middle,29 inch bike motor kit works forward. Be right side,hub motor works bacwkard / reverse…

2.Green button is used to control cruise, while electric bike motor is running,also over some speed,example: over 1/3 max speed,at this time,press green button one time,then loose throttle,LCD display “C”,motor will works the same speed. Re-press this green button one time or press brake lever or turn throttle to max, electric bike motor will stop.

3.Red button be up,regen on. Be down,regen off. This regen is not strong.Only while braking with a little regen.

Questions regarding your DIY conversion kits

Posted by on December 29, 2021 Comments Off on Questions regarding your DIY conversion kits

Q:I assume your electric hub motor bike conversion kits are speed limited, consider for example your 250W 36V hub motor bike conversion kits. Usually it seems the speed limit it set to something like 25 kmph, or so.

I building a custom bicycle and I am interested in knowing if this speed limit can be configured to be higher. I guess I am thinking this possibly is the case if one can simply enter a lower wheel size when configuring the controller. Could this be there case, or is there may be some other way to do this using your kit?

Also, are you by any chance the same company as leaf bike? And if so, does this answer also apply to the e-bike conversion kits sold under that name, e.g. their 250 W 24 V conversion kits?

A: Yes, our controller has speed limit.
There is max speed display on our leafbike.com site.
We set LCD as wheel size.For 12inch,14inch,16inch,18inch,20inch,24inch,26inch,27inch,27.5inch,700c,28inch and 29 inch..
For example: our site write: max 70kmh ( You can limit max speed under 70kmh,from min 6kmh to max 70kmh)
our site write: max 24kmh ( You can limit max speed under 24kmh,from min 6kmh to max 24kmh)

Q: Thanks for the info. Just so that I understand correctly, let me ask these questions:

For example, considering your DIY e-bike kit 700c hub motor kit front wheel, Item ID #LBCK700C24250FM”. Our your web-site, says that it is speed limited to 36.1 kmh (actually used to say something like 25 kmh, you increased it?). Though this speed seems sufficient (now) I still wonder if I can modify this speed limit in some way. Say, if I configure the controller to a wheel size smaller than 700c. If that it possible I am thinking the max speed would be increased. Is that something that is user configurable, or it is hard coded into the controller that it is for a 700c wheel?

Is it also maybe the case that the controller that one get if one buys, say , this kit also works with some more powerful motors? But maybe it is limited to the operating voltage of 24 V?

Do you have recommendations as to if one should go with, say, a 24V or a 36V system?

Finally, I note on the web-site I list above, seems that you are showing the motor performance table for a 36V motor. Could it be that it should show the performance of the attached motor data for a 24V motor?

Just another question here.

For your 36V 250W front wheel DIY kit, the max speed is listed as 26.3 kmh or 16.4 mph. This seems that it can be a bit limiting for some jurisdictions. Is it maybe the case that you have increased this max speed also to 36.1 kmh as listed for the 24V version? And, also, here, can I configure it for a lower bike speed to make it go faster or is there some other way to increase this speed limit?

By the way, I see the advantage with the 36 V systems. You get more watt-hours in your battery. Seems like better choice for my use case.

How to replace winding rotor of hub motor ?

Posted by on December 29, 2021 Comments Off on How to replace winding rotor of hub motor ?

If your hub motor has issue..How to replace winding rotor?
It takes about 10 minutes to replace. Very easy.
Tool: ONLY ONE M4 Inner hexagon spanner
Do it as below / uninstall Disconnect:
1. Disconnect 16 pcs of screw nut from your hub motor (two side) – It takes about 3 minutes to do it.
2. Knock the shaft end (NO cable side) on the ground,then the cover will off from hub – It takes 2 seconds to do it.
3. Two hands hold on hub(Not rim), still knock the shaft end (No cable side) on the ground,then the whole of winding rotor will out of hub.. – It takes 2 seconds to to it.

Do it as below / Install:
1. Put the cover on the hub and put 8 pcs of screw nut on..tight them. – It takes about 2 minutes to do it.
2. Check and make sure no other thing around magnet – It takes 10 seconds to check it.
3. Put the whole of winding rotor into hub – It takes 2 seconds to do it.
4. Put the other 8 pcs of screw nut on – It takes about 2 minutes to do it.

electric bike motor 48v 1000w leaf

Posted by on December 29, 2021 Comments Off on electric bike motor 48v 1000w leaf

Only the electric bike motor. I will not use tire. I will not use rim. I only use 48v 1000w motor.If it works for me I will purchase many of them. (But, yes, I also need the electric motor controller)

Small size is not the only criteria.I seek powerful motor.But the hub motor alone needs to fit in 152mm diameter tube. (no rim needed. It wastes space.)

I have many questions.

I am serious buyer. I don’t make bikes or scooters. I seek your hub motors for use in my equipment, and will buy many of them when I find what works for me.

I realize you don’t have all the information easily available now. But please invest more time in answering my questions more completely:

1. Dimensions of 1000w hub motor alone. (48v-1000watt electric motorcycle motor) Weight of hub motor alone.

2. Data showing torque, energy use, and efficiency of that motor when at 120 to 140 rpm. (projected, if need be)

3. Which electronic controller would be the best, and what is its cost. I can use any voltage. I use grid power, and not use electric bike batteries.

4. Please give me a cost when ordering in quantities of 5, 10, 50, 100, and 200. Also including the cost of controllers as an option would be helpful to me.

I assume they’d be boxed in groups of 5 or more, so please determine what shipping. It would be very good.

If this information is not available through you, please send me the contact information I would be able to use myself, and I will find someone here to translate language so it is easier to communicate. I think you have the hub motors I need, but I need to verify it will work for me.

hub motor selection and rim width.

Posted by on December 29, 2021 Comments Off on hub motor selection and rim width.

I am looking to build an e-bike, starting with the Mongoose Dolomite. 5000W is probably too much, I see you offer 1500W hub motor kits, but I did not see any information about 4inch wheels for the fat tire bikes.
Do you have a 26 inch bike motor kit for the 26 inch fat tire bikes, rear drive, 1500W or more?
With a 9 speed cassette is there enough room for the hub motor in a 135mm drop out ?
I see now that my Shimano 9 speed rear cassette should be the same width as a Shimano 7 speed. It is the spacing of each gear that is different. However, if I am to purchase your kit, I would need you to supply the 9 speed freewheel because I assume your hub motors use freewheels and not cassettes. Right now my bike is a cassette.

Unless it is possible to supply this bike motor in the kit instead:

I should be able to mount my cassette to this motor. Can we do that instead?

This is no longer for fat tire bike so please ignore the first email about the fat tire kit.

It is for a regular mountain bike so no need to worry about 3 or 4″ tires. I have regular mountain bike tires, 26 x 2″ right now. Once I do the electric bike conversion kit, I may switch to more narrow road tires like 1.5″ or 1.75″ so the regular double wall mountain bike rim is fine.

So I made a new order with the individual parts and I excluded the brakes because I do not need them. However, it came out to be a little more expensive than selecting the kit but, I would like a double walled 26″ rim added to the hub motor please.

Just wondering what type of connectors come on the motor controller? I am ordering my battery and need to know what kind of connectors it has. Do you have any pictures or description?